Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
They are making a few good annotation regarding Installing A Bathtub as a whole in the content down below.
Mounting a bath tub isn't exactly rocket science, however it does call for strong plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is likewise a moderately challenging job. If the old tub is readily accessible, the task can relocate rapidly; if you have to open a wall surface to remove the old bathtub and position the brand-new bathtub, the job is a lot harder. In either case, the job is within a house handyman's abilities, although you will need an assistant to leave the old bathtub and set in the new one. See to it you have actually certified on your own for the work and also fit attempting it. Rather than employing a contractor to take control of a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Opportunities are you may require a specialist plumber to make tube connections.
This post will assist you set up a new bathtub in your washroom if you have currently bought a new tub and also don't require to alter the arrangement of your previous water supply pipelines.
Your devices and also product list should consist of the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water. After doing so, switch on the faucets to drain any water continuing to be in the system. The process of removing the existing faucets can be fairly bothersome because of the restricted gain access to that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipes. When the supply pipelines have been gotten rid of, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming throughout this procedure. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a link to the current supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washers remain in location between the faucet and also the sink. Secure the faucet in place with the supplier offered backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The former kind needs to be attached to the tap ends first, tightening just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Using the two wood boards under its feet, position the tub in the required position. The wooden boards are valuable in evenly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto 4 small factors.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level as well as readjusting the feet on the bathtub until the spirit level checks out degree.
To install taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Activate the water supply and examine all joints and also brand-new pipework for leaks and tighten them if essential. Load the tub and additionally examine the overflow outlet and also the regular outlet for leakages.
Finally, fix the bathroom paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bathtub ought to wait until the tub has been utilized at the very least when as this will settle it into its last placement.
Getting ready for the Setup
Firstly, the sustaining framework supplied with the bath ought to be fitted (if required) according to the maker's directions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the tap includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two faucets using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. See to it you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to break a stiff seal, causing the water to penetrate the wall in between the bath as well as the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the tub with water prior to sealing, to enable the motion experienced when the bathtub is in usage. The sealant can split fairly early if you do not consider this activity prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily offered on the market. It is a good idea to fit the tiles using water-resistant or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We hope you liked our part on How to Install a Bathtub. Thank you for finding the time to read our blog. Enjoyed our piece? Please share it. Help another person find it. We enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.
Dial, rest easy! Report this page